voici le contenu de l a commande :
[alain@localhost alain]$ su
Password:
[root@localhost alain]# cdrecord dev=0,3,0 -scanbus
Cdrecord-Clone 2.01a26-dvd (i686-pc-linux-gnu) Copyright (C) 1995-2004
Jörg Schilling
Note: This version is an unofficial (modified) version with DVD support
Note: and therefore may have bugs that are not present in the original.
Note: Please send bug reports or support requests to
<warly@???>.
Note: The author of cdrecord should not be bothered with problems in
this version.
scsidev: '0,3,0'
scsibus: 0 target: 3 lun: 0
Linux sg driver version: 3.5.30
Using libscg version 'schily-0.8'.
scsibus0:
0,0,0 0) *
0,1,0 1) *
0,2,0 2) *
Nooks L. Affro a écrit :
>Bonjour,
>
>La gravure agit sur le device generique scsi ( sg ) et pas sur le cdrom scsi ( scd ).
>
>Ton graveur est la :
>
>Attached scsi generic sg0 at scsi0, channel 0, id 3, lun 0, type 5
>
>Donc, tout doit bien marcher ... en tout cas cote noyau.
>
>que donne ceci :
>
>cdrecord dev=0,3,0 -scanbus
>
>?
>
>
>Nooks.
>
>On Sun, Jun 27, 2004 at 07:16:37PM +0200, alain.laposte wrote:
>
>
>>Voici le contenu de dmesg en totalité j'ai agrandi la sectiob du graveur
>>yamaha en scsi.
>>dmseg:
>>
>>tected mode interface info at c000:0336
>>vesafb: scrolling: redraw
>>vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
>>fb0: VESA VGA frame buffer device
>>SBF: Simple Boot Flag extension found and enabled.
>>SBF: Setting boot flags 0x1
>>apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
>>ikconfig 0.7 with /proc/config*
>>VFS: Disk quotas dquot_6.5.1
>>devfs: 2004-01-31 Richard Gooch (rgooch@???)
>>devfs: boot_options: 0x1
>>Initializing Cryptographic API
>>isapnp: Scanning for PnP cards...
>>isapnp: No Plug & Play device found
>>bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size
>>14856 bytes, found (800x600, 14808 bytes, v3).
>>Console: switching to colour frame buffer device 92x32
>>pty: 1024 Unix98 ptys configured
>>Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
>>ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>>RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
>>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
>>VIA8237SATA: IDE controller at PCI slot 0000:00:0f.0
>>PCI: Found IRQ 4 for device 0000:00:0f.0
>>IRQ routing conflict for 0000:00:0f.0, have irq 9, want irq 4
>>IRQ routing conflict for 0000:00:10.2, have irq 9, want irq 4
>>IRQ routing conflict for 0000:00:10.3, have irq 9, want irq 4
>>VIA8237SATA: chipset revision 128
>>VIA8237SATA: 100% native mode on irq 9
>> ide0: BM-DMA at 0xa800-0xa807, BIOS settings: hda:pio, hdb:pio
>> ide1: BM-DMA at 0xa808-0xa80f, BIOS settings: hdc:pio, hdd:pio
>>VP_IDE: IDE controller at PCI slot 0000:00:0f.1
>>PCI: Found IRQ 3 for device 0000:00:0f.1
>>PCI: Sharing IRQ 3 with 0000:00:10.0
>>PCI: Sharing IRQ 3 with 0000:00:10.1
>>PCI: Sharing IRQ 3 with 0000:00:12.0
>>VP_IDE: chipset revision 6
>>VP_IDE: not 100% native mode: will probe irqs later
>>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
>>VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
>> ide2: BM-DMA at 0xa000-0xa007, BIOS settings: hde:DMA, hdf:pio
>> ide3: BM-DMA at 0xa008-0xa00f, BIOS settings: hdg:DMA, hdh:DMA
>>hde: IC35L120AVV207-0, ATA DISK drive
>>Using anticipatory io scheduler
>>ide2 at 0x1f0-0x1f7,0x3f6 on irq 14
>>hdg: WDC AC38400L, ATA DISK drive
>>hdh: SONY CDU4811, ATAPI CD/DVD-ROM drive
>>ide3 at 0x170-0x177,0x376 on irq 15
>>hde: max request size: 1024KiB
>>hde: 241254720 sectors (123522 MB) w/1821KiB Cache, CHS=16383/255/63,
>>UDMA(33)
>>/dev/ide/host2/bus0/target0/lun0: p1
>>hdg: max request size: 128KiB
>>hdg: 16514064 sectors (8455 MB) w/256KiB Cache, CHS=16383/16/63, UDMA(33)
>>/dev/ide/host2/bus1/target0/lun0: p1 p2 < p5 p6 >
>>Console: switching to colour frame buffer device 92x32
>>mice: PS/2 mouse device common for all mice
>>serio: i8042 AUX port at 0x60,0x64 irq 12
>>input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
>>serio: i8042 KBD port at 0x60,0x64 irq 1
>>input: AT Translated Set 2 keyboard on isa0060/serio0
>>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
>>EISA: Probing bus 0 at eisa0
>>NET: Registered protocol family 2
>>IP: routing cache hash table of 2048 buckets, 16Kbytes
>>TCP: Hash tables configured (established 16384 bind 32768)
>>NET: Registered protocol family 1
>>BIOS EDD facility v0.12 2004-Jan-26, 2 devices found
>>Please report your BIOS at http://linux.dell.com/edd/results.html
>>Resume Machine: resuming from /dev/hdg5
>>Resuming from device hdg5
>>Resume Machine: This is normal swap space
>>PM: Reading pmdisk image.
>>PM: Resume from disk failed.
>>md: Autodetecting RAID arrays.
>>md: autorun ...
>>md: ... autorun DONE.
>>RAMDISK: Compressed image found at block 0
>>VFS: Mounted root (ext2 filesystem).
>>Mounted devfs on /dev
>>SCSI subsystem initialized
>>PCI: Found IRQ 10 for device 0000:00:0b.0
>>
>>ahc_pci:0:11:0: Host Adapter Bios disabled. Using default SCSI device
>>parameters
>>scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
>> <Adaptec 2902/04/10/15/20C/30C SCSI adapter>
>> aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
>>
>>(scsi0:A:3): 10.000MB/s transfers (10.000MHz, offset 15)
>> Vendor: YAMAHA Model: CRW8424S Rev: 1.0d
>> Type: CD-ROM ANSI SCSI revision: 02
>>
>>libata version 1.00 loaded.
>>kjournald starting. Commit interval 5 seconds
>>EXT3-fs: mounted filesystem with ordered data mode.
>>Mounted devfs on /dev
>>Freeing unused kernel memory: 272k freed
>>Real Time Clock Driver v1.12
>>drivers/usb/core/usb.c: registered new driver usbfs
>>drivers/usb/core/usb.c: registered new driver hub
>>drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface
>>driver v2.1
>>PCI: Found IRQ 3 for device 0000:00:10.0
>>PCI: Sharing IRQ 3 with 0000:00:0f.1
>>PCI: Sharing IRQ 3 with 0000:00:10.1
>>PCI: Sharing IRQ 3 with 0000:00:12.0
>>uhci_hcd 0000:00:10.0: UHCI Host Controller
>>uhci_hcd 0000:00:10.0: irq 3, io base 00009800
>>uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
>>hub 1-0:1.0: USB hub found
>>hub 1-0:1.0: 2 ports detected
>>PCI: Found IRQ 3 for device 0000:00:10.1
>>PCI: Sharing IRQ 3 with 0000:00:0f.1
>>PCI: Sharing IRQ 3 with 0000:00:10.0
>>PCI: Sharing IRQ 3 with 0000:00:12.0
>>uhci_hcd 0000:00:10.1: UHCI Host Controller
>>uhci_hcd 0000:00:10.1: irq 3, io base 00009400
>>uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
>>hub 2-0:1.0: USB hub found
>>hub 2-0:1.0: 2 ports detected
>>PCI: Found IRQ 4 for device 0000:00:10.2
>>IRQ routing conflict for 0000:00:0f.0, have irq 9, want irq 4
>>IRQ routing conflict for 0000:00:10.2, have irq 9, want irq 4
>>IRQ routing conflict for 0000:00:10.3, have irq 9, want irq 4
>>uhci_hcd 0000:00:10.2: UHCI Host Controller
>>uhci_hcd 0000:00:10.2: irq 9, io base 00009000
>>uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
>>usb 1-1: new full speed USB device using address 2
>>hub 3-0:1.0: USB hub found
>>hub 3-0:1.0: 2 ports detected
>>PCI: Found IRQ 4 for device 0000:00:10.3
>>IRQ routing conflict for 0000:00:0f.0, have irq 9, want irq 4
>>IRQ routing conflict for 0000:00:10.2, have irq 9, want irq 4
>>IRQ routing conflict for 0000:00:10.3, have irq 9, want irq 4
>>uhci_hcd 0000:00:10.3: UHCI Host Controller
>>uhci_hcd 0000:00:10.3: irq 9, io base 00008800
>>uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
>>hub 4-0:1.0: USB hub found
>>hub 4-0:1.0: 2 ports detected
>>PCI: Assigned IRQ 11 for device 0000:00:10.4
>>PCI: Sharing IRQ 11 with 0000:00:11.5
>>ehci_hcd 0000:00:10.4: EHCI Host Controller
>>ehci_hcd 0000:00:10.4: irq 11, pci mem d0c09000
>>ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
>>ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
>>hub 5-0:1.0: USB hub found
>>hub 5-0:1.0: 8 ports detected
>>drivers/usb/core/usb.c: registered new driver usblp
>>drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
>>hub 1-0:1.0: connect-debounce failed, port 2 disabled
>>EXT3 FS on hdg1, internal journal
>>imm: Version 2.05 (for Linux 2.4.0)
>>parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
>>parport0: irq 7 detected
>>parport0: cpp_daisy: aa5500ff(38)
>>parport0: assign_addrs: aa5500ff(38)
>>parport0: cpp_daisy: aa5500ff(38)
>>parport0: assign_addrs: aa5500ff(38)
>>ppa: Version 2.07 (for Linux 2.4.x)
>>Linux agpgart interface v0.100 (c) Dave Jones
>>agpgart: Detected VIA KT400/KT400A/KT600 chipset
>>agpgart: Maximum main memory to use for agp memory: 203M
>>agpgart: AGP aperture is 64M @ 0xf8000000
>>kjournald starting. Commit interval 5 seconds
>>EXT3 FS on hdg6, internal journal
>>EXT3-fs: mounted filesystem with ordered data mode.
>>Supermount version 2.0.4 for kernel 2.6
>>usb 2-1: new low speed USB device using address 2
>>drivers/usb/core/usb.c: registered new driver hiddev
>>drivers/usb/input/hid-ff.c: hid_ff_init could not find initializer
>>input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with
>>IntelliEye(TM)] on usb-0000:00:10.1-1
>>drivers/usb/core/usb.c: registered new driver hid
>>drivers/usb/input/hid-core.c: v2.0:USB HID core driver
>>drivers/usb/core/usb.c: registered new driver usbmouse
>>drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
>>usb 2-2: new full speed USB device using address 3
>>ts: Compaq touchscreen protocol output
>>drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0
>>alt 0 proto 2 vid 0x03F0 pid 0x6204
>>usb 1-1: USB disconnect, address 2
>>usb 1-1: new full speed USB device using address 3
>>usb 1-2: new low speed USB device using address 4
>>drivers/usb/input/hid-ff.c: hid_ff_init could not find initializer
>>input: USB HID v1.00 Keyboard [0430:0005] on usb-0000:00:10.0-2
>>drivers/usb/core/usb.c: registered new driver usbkbd
>>drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
>>via-rhine.c:v1.10-LK1.1.19-2.5 July-12-2003 Written by Donald Becker
>> http://www.scyld.com/network/via-rhine.html
>>PCI: Found IRQ 3 for device 0000:00:12.0
>>PCI: Sharing IRQ 3 with 0000:00:0f.1
>>PCI: Sharing IRQ 3 with 0000:00:10.0
>>PCI: Sharing IRQ 3 with 0000:00:10.1
>>eth0: VIA VT6102 Rhine-II at 0x8400, 00:0e:a6:78:7a:26, IRQ 3.
>>eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1.
>>ip_tables: (C) 2000-2002 Netfilter core team
>>ip_conntrack version 2.1 (2047 buckets, 16376 max) - 300 bytes per conntrack
>>inserting floppy driver for 2.6.3-4mdk
>>Floppy drive(s): fd0 is 1.44M
>>FDC 0 is a post-1991 82077
>>hdh: ATAPI 48X CD-ROM drive, 120kB Cache, UDMA(33)
>>Uniform CD-ROM driver Revision: 3.20
>>ide-floppy driver 0.99.newide
>>sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
>>Attached scsi CD-ROM sr0 at scsi0, channel 0, id 3, lun 0
>>Device not ready. Make sure there is a disc in the drive.
>>Device not ready. Make sure there is a disc in the drive.
>>NET: Registered protocol family 17
>>eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
>>via82xx: Assuming DXS channels with 48k fixed sample rate.
>> Please try dxs_support=1 or dxs_support=4 option
>> and report if it works on your machine.
>>PCI: Found IRQ 11 for device 0000:00:11.5
>>PCI: Sharing IRQ 11 with 0000:00:10.4
>>PCI: Setting latency timer of device 0000:00:11.5 to 64
>>codec_read: codec 0 is not valid [0xfe0000]
>>codec_read: codec 0 is not valid [0xfe0000]
>>codec_read: codec 0 is not valid [0xfe0000]
>>codec_read: codec 0 is not valid [0xfe0000]
>>NET: Registered protocol family 10
>>Disabled Privacy Extensions on device c035fa20(lo)
>>IPv6 over IPv4 tunneling driver
>>mtrr: 0xf6000000,0x2000000 overlaps existing 0xf6000000,0x400000
>>lp0: using parport0 (polling).
>>lp0: console ready
>>Attached scsi generic sg0 at scsi0, channel 0, id 3, lun 0, type 5
>>eth0: no IPv6 routers present
>>Installing knfsd (copyright (C) 1996 okir@???).
>>Device not ready. Make sure there is a disc in the drive.
>>Device not ready. Make sure there is a disc in the drive.
>>bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600,
>>11943 bytes, v3).
>>bootsplash: status on console 0 changed to on
>>bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600,
>>11943 bytes, v3).
>>bootsplash: status on console 1 changed to on
>>bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600,
>>11943 bytes, v3).
>>bootsplash: status on console 2 changed to on
>>bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600,
>>11943 bytes, v3).
>>bootsplash: status on console 3 changed to on
>>bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600,
>>11943 bytes, v3).
>>bootsplash: status on console 4 changed to on
>>bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600,
>>11943 bytes, v3).
>>bootsplash: status on console 5 changed to on
>>Device not ready. Make sure there is a disc in the drive.
>>.
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>Christian Marillat a écrit :
>>
>>
>>
>>>"alain.laposte" <alain.morellec@???> writes:
>>>
>>>[Merci de répondre dans le bon sens]
>>>
>>>
>>>
>>>
>>>
>>>>Cest pour un noyau 2.6 de la mandrake 10.
>>>>
>>>>
>>>>
>>>>
>>>Dans tes logs il n'y a pas de graveur de CD. Il est ou exactement ?
>>>
>>>hde: IC35L120AVV207-0, ATA DISK drive
>>>hdg: WDC AC38400L, ATA DISK drive
>>>hdh: SONY CDU4811, ATAPI CD/DVD-ROM drive
>>>
>>>Christian
>>>
>>>
>>>
>>>
>>>
>>
>>
>>
>>
>
>
>
