voila, j ai fait les deux fichiers de logs.
j ai remarque que sous knoppix (ou meme debian) le disque fonctionne en
usb 1.1, alors que sous redhat 9 il essaye de fonctionner en usb 2.0...
comment puis je forcer le fonctionnement en usb 1.1 temporairement ?
Le mar 09/03/2004 à 10:59, Stephane Driussi a écrit :
> il faut comparer la config des noyaux knoopix et redhat. Compare les
> dmesg des deux linux, il y a la solution.
> Eventuellement envoie nous le resultat des deux linux apres juste le
> pluguage du disque dur (pas de mount ni lecture)
>
> Stephane
>
> Christophe Noilhac wrote:
>
> >Je me reponds a moi meme :)
> >
> >il semble que le module nls_cp437 soit une police Microsft... donc rien
> >de tres important dans mon cas.
> >
> >
> >sinon, je peux exclure totalement l incompatibilite materielle, j ai
> >essaye sur la machine en question avec knoppix 3.3, et ca marche nickel.
> >
> >
> >je sais pas trop ou chercher la... au secours !
> >
> >
> >
>
>
Linux version 2.4.22-xfs (root@Knoppix) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Fr Okt 3 20:36:25 CEST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001bffc000 (usable)
BIOS-e820: 000000001bffc000 - 000000001bfff000 (ACPI data)
BIOS-e820: 000000001bfff000 - 000000001c000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
447MB LOWMEM available.
On node 0 totalpages: 114684
zone(0): 4096 pages.
zone(1): 110588 pages.
zone(2): 0 pages.
Kernel command line: ramdisk_size=100000 init=/etc/init lang=us apm=power-off hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi vga=791 initrd=miniroot.gz nomce quiet BOOT_IMAGE=knoppix BOOT_IMAGE=vmlinuz lang=fr
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Found and enabled local APIC!
Initializing CPU#0
Detected 2000.157 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 3984.58 BogoMIPS
Memory: 450052k/458736k available (1262k kernel code, 8296k reserved, 534k data, 132k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
CPU: Hyper-Threading is disabled
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@???)
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
CPU: Hyper-Threading is disabled
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU0: Intel(R) Celeron(R) CPU 2.00GHz stepping 09
per-CPU timeslice cutoff: 365.69 usecs.
SMP motherboard not detected.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2000.2078 MHz.
..... host bus clock speed is 100.0102 MHz.
cpu: 0, clocks: 1000102, slice: 500051
CPU0<T0:1000096,T1:500032,D:13,S:500051,C:1000102>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xf1070, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [1039/0962] at 00:02.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xe8000000, mapped to 0xdc80d000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at cb37:000c
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0xa400-0xa407, BIOS settings: hda:DMA, hdb:DMA
hda: Maxtor 6Y200P0, ATA DISK drive
hdb: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 398297088 sectors (203928 MB) w/2048KiB Cache, CHS=24792/255/63
ide-cd: passing drive hdb to ide-scsi emulation.
hdb: attached ide-scsi driver.
Partition check:
hda: hda1 hda2 hda3 hda4
ide: late registration of driver.
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.02
Guestimating sector 398267159 for superblock
driver for Silicon Image(tm) Medley(tm) hardware version 0.0.1: No raid array found
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: IDE Model: DVD-ROM 16X Rev: 1p21
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 478k freed
VFS: Mounted root (ext2 filesystem).
NCR53c406a: no available ports found
aec671x_detect:
scsi: <fdomain> Detection failed (no card)
GDT: Storage RAID Controller Driver. Version: 2.05
GDT: Found 0 PCI Storage RAID Controllers
megaraid: v1.18f (Release Date: Tue Dec 10 09:54:39 EST 2002)
megaraid: no BIOS enabled.
DC390: 0 adapters found
Failed initialization of WD-7000 SCSI card!
ISO 9660 Extensions: Microsoft Joliet Level 3
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v2.00
cloop: /cdrom/KNOPPIX/KNOPPIX: 29973 blocks, 65536 bytes/block, largest block is 65562 bytes.
cloop: loaded (max 8 devices)
ISO 9660 Extensions: RRIP_1991A
Freeing unused kernel memory: 132k freed
Real Time Clock Driver v1.10e
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
Yenta IRQ list 0080, PCI irq11
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0820-0x08ff: clean.
cs: IO port probe 0x0800-0x080f: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x290-0x297 0x378-0x37f 0x3f8-0x3ff 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 20:50:29 Oct 3 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb-ohci.c: USB OHCI at membase 0xdcbb3000, IRQ 5
usb-ohci.c: usb-00:03.0, Silicon Integrated Systems [SiS] USB 1.0 Controller
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-ohci.c: USB OHCI at membase 0xdcbb5000, IRQ 6
usb-ohci.c: usb-00:03.1, Silicon Integrated Systems [SiS] USB 1.0 Controller (#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-ohci.c: USB OHCI at membase 0xdcbb7000, IRQ 9
usb-ohci.c: usb-00:03.2, Silicon Integrated Systems [SiS] USB 1.0 Controller (#3)
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usbdevfs: remount parameter error
hub.c: new USB device 00:03.0-1, assigned address 2
usb.c: USB device 2 (vend/prod 0xbc7/0x4) is not claimed by any active driver.
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Redundant entry in serial pci_table. Please send the output of
lspci -vv, this message (134d,7892,134d,0001)
and the manufacturer and name of serial board or modem board
to serial-pci-info@???.
register_serial(): autoconfig failed
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
Linux video capture interface: v1.00
i2c-core.o: i2c core module
i2c-algo-bit.o: i2c bit algorithm module
bttv: driver version 0.7.107 loaded
bttv: using 4 buffers with 2080k (8320k total) for capture
bttv: Host bridge is Silicon Integrated Systems [SiS] SiS651 Host
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 00:0e.0, irq: 10, latency: 32, mmio: 0xe7000000
bttv0: detected: Leadtek WinFast TV 2000 [card=34], PCI subsystem ID is 107d:6606
bttv0: using: BT878(Leadtek WinFast 2000/ W) [card=34,autodetected]
i2c-core.o: adapter bt848 #0 registered as adapter 0.
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
i2c-core.o: driver i2c TV tuner driver registered.
tuner: chip found @ 0xc2
tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
i2c-core.o: client [Philips PAL_BG (FI1216 and comp] registered to adapter [bt848 #0](pos. 0).
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
Broadcom 4401 Ethernet Driver bcm4400 ver. 1.0.1 (08/26/02)
eth0: Broadcom BCM4401 100Base-T found at mem d4800000, IRQ 15, node addr 000c6eaf114e
Intel 810 + AC97 Audio, version 0.24, 20:49:17 Oct 3 2003
i810: SiS 7012 found at IO 0x9000 and 0x9400, MEM 0x0000 and 0x0000, IRQ 15
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 Audio codec, id: ALG32 (ALC650)
i810_audio: AC'97 codec 0, new EID value = 0x05c7
i810_audio: AC'97 codec 0, DAC map configured, total channels = 6
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 380M
agpgart: Detected SiS 651 chipset
agpgart: AGP aperture is 128M @ 0xd8000000
Adding Swap: 514072k swap-space (priority -1)
bcm4400: eth0 NIC Link is Down
Warning: Remapping obsolete /dev/fb* minor 32 to 1
Warning: Remapping obsolete /dev/fb* minor 64 to 2
Warning: Remapping obsolete /dev/fb* minor 96 to 3
Warning: Remapping obsolete /dev/fb* minor 128 to 4
Warning: Remapping obsolete /dev/fb* minor 160 to 5
Warning: Remapping obsolete /dev/fb* minor 192 to 6
Warning: Remapping obsolete /dev/fb* minor 224 to 7
hub.c: new USB device 00:03.1-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x5e3/0x702) is not claimed by any active driver.
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi2 : SCSI emulation for USB Mass Storage devices
Vendor: IC35L080 Model: AVVA07-0 Rev: 0811
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: sda1 sda2
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
us 301, change 0, 1.5 Mb/s
hub.c: port 1, portstatus 301, change 0, 1.5 Mb/s
hub.c: port 1, portstatus 301, change 0, 1.5 Mb/s
hub.c: port 1, portstatus 303, change 10, 1.5 Mb/s
hub.c: new USB device 00:03.0-1, assigned address 2
usb.c: kmalloc IF db927ae0, numif 1
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
usb.c: USB device number 2 default language ID 0x409
Manufacturer: X10 Wireless Technology Inc
Product: USB Receiver
usb.c: unhandled interfaces on device
usb.c: USB device 2 (vend/prod 0xbc7/0x4) is not claimed by any active driver.
Length = 18
DescriptorType = 01
USB version = 1.10
Vendor:Product = 0bc7:0004
MaxPacketSize0 = 8
NumConfigurations = 1
Device version = 1.00
Device Class:SubClass:Protocol = 00:00:00
Per-interface classes
Configuration:
bLength = 9
bDescriptorType = 02
wTotalLength = 0020
bNumInterfaces = 01
bConfigurationValue = 01
iConfiguration = 00
bmAttributes = 80
MaxPower = 2mA
Interface: 0
Alternate Setting: 0
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 00
bNumEndpoints = 02
bInterface Class:SubClass:Protocol = ff:00:00
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 03 (Interrupt)
wMaxPacketSize = 0008
bInterval = 0a
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 02 (out)
bmAttributes = 03 (Interrupt)
wMaxPacketSize = 0008
bInterval = 0a
usb.c: kusbd: /sbin/hotplug add 2
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,4), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ohci1394: $Rev: 1045 $ Ben Collins <bcollins@???>
ohci1394_0: Unexpected PCI resource length of 1000!
ohci1394_0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[d7000000-d70007ff] Max Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000013dac3]
lirc_dev: IR Remote Control driver registered, at major 61
lirc_atiusb: USB remote driver for LIRC v0.3
lirc_atiusb: Paul Miller <pmiller9@???>
lirc_atiusb: debug mode enabled
usb.c: registered new driver lirc_atiusb
lirc_atiusb: usb probe called
lirc_atiusb[2]: bytes_in_key=5 len=8 maxp=8 buf_len=5
lirc_dev: lirc_register_plugin:sample_rate: 0
lirc_atiusb[2]: X10 Wireless Technology Inc USB Receiver on usb1:2
lirc_atiusb[2]: send called (0x8004)
lirc_atiusb[2]: usb out called
lirc_atiusb[2]: send complete (0x8004)
lirc_atiusb[2]: usb out called
lirc_atiusb[2]: send called (0x8007)
lirc_atiusb[2]: usb out called
lirc_atiusb[2]: send complete (0x8007)
lirc_atiusb[2]: usb out called
usb.c: lirc_atiusb driver claimed interface db927ae0
uhci.c: USB Universal Host Controller Interface driver v1.1
Broadcom 4401 Ethernet Driver bcm4400 ver. 3.0.7 (10/31/03)
eth0: Broadcom BCM4401 100Base-T found at mem d4800000, IRQ 12, node addr 000c6eaf114e
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x290-0x297 0x378-0x37f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
apm: overridden by ACPI.
bcm4400: eth0 NIC Link is Up, 100 Mbps full duplex
lirc_atiusb[2]: set use inc
lirc_atiusb[2]: data received (length 1)
Intel 810 + AC97 Audio, version 0.24, 12:40:54 Feb 8 2004
i810: SiS 7012 found at IO 0x9000 and 0x9400, MEM 0x0000 and 0x0000, IRQ 12
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 Audio codec, id: ALG32 (ALC650)
i810_audio: AC'97 codec 0, new EID value = 0x05c7
i810_audio: AC'97 codec 0, DAC map configured, total channels = 6
ehci_hcd 00:03.3: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC
hub.c: port 1, portstatus 0, change 1, 12 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 0, change 1, 12 Mb/s
ehci_hcd 00:03.3: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub.c: port 2, portstatus 501, change 1, 480 Mb/s
hub.c: port 2 connection change
hub.c: port 2, portstatus 501, change 1, 480 Mb/s
hub.c: port 2, portstatus 501, change 0, 480 Mb/s
hub.c: port 2, portstatus 501, change 0, 480 Mb/s
hub.c: port 2, portstatus 501, change 0, 480 Mb/s
hub.c: port 2, portstatus 501, change 0, 480 Mb/s
hub.c: port 2, portstatus 511, change 0, 480 Mb/s
hub.c: port 2 of hub 1 not reset yet, waiting 10ms
hub.c: port 2, portstatus 511, change 0, 480 Mb/s
hub.c: port 2 of hub 1 not reset yet, waiting 10ms
ehci_hcd 00:03.3: port 2 high speed
ehci_hcd 00:03.3: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
hub.c: port 2, portstatus 503, change 10, 480 Mb/s
hub.c: new USB device 00:03.3-2, assigned address 2
usb.c: kmalloc IF d5911ba0, numif 1
usb.c: new device strings: Mfr=0, Product=1, SerialNumber=0
usb.c: USB device number 2 default language ID 0x409
Product: USB TO IDE
usb.c: unhandled interfaces on device
usb.c: USB device 2 (vend/prod 0x5e3/0x702) is not claimed by any active driver.
Length = 18
DescriptorType = 01
USB version = 2.00
Vendor:Product = 05e3:0702
MaxPacketSize0 = 64
NumConfigurations = 1
Device version = 0.02
Device Class:SubClass:Protocol = 00:00:00
Per-interface classes
Configuration:
bLength = 9
bDescriptorType = 02
wTotalLength = 0020
bNumInterfaces = 01
bConfigurationValue = 01
iConfiguration = 00
bmAttributes = c0
MaxPower = 96mA
Interface: 0
Alternate Setting: 0
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 00
bNumEndpoints = 02
bInterface Class:SubClass:Protocol = 08:06:50
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0200
bInterval = 01
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 02 (out)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0200
bInterval = 01
usb.c: kusbd: /sbin/hotplug add 2
hub.c: port 3, portstatus 100, change 0, 12 Mb/s
hub.c: port 4, portstatus 100, change 0, 12 Mb/s
hub.c: port 5, portstatus 100, change 0, 12 Mb/s
hub.c: port 6, portstatus 100, change 0, 12 Mb/s
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
usb-storage: act_altsettting is 0
usb-storage: id_index calculated to be: 103
usb-storage: Array length appears to be: 105
usb-storage: USB Mass Storage device detected
usb-storage: Endpoints: In: 0xda0d7220 Out: 0xda0d7234 Int: 0x00000000 (Period 0)
usb-storage: New GUID 05e307020000000000000000
usb-storage: GetMaxLUN command result is 1, data is 0
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: *** thread sleeping.
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 ff 00 39 db ac e6 69 db
usb-storage: Bulk command S 0x43425355 T 0x1 Trg 0 LUN 0 L 255 F 128 CL 6
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 255 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 40/255
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_clear_halt: result=0
usb-storage: Attempting to get CSW (2nd try)...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x1 R 215 Stat 0x0
usb-storage: Fixing INQUIRY data to show SCSI rev 2 - was 0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: IC35L080 Model: AVVA07-0 Rev: 0811
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0/1)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7/0)
usb-storage: *** thread sleeping.
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00 00 00 00 00 00 00
usb-storage: Bulk command S 0x43425355 T 0x2 Trg 0 LUN 0 L 0 F 0 CL 6
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x2 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00 00 00
usb-storage: Bulk command S 0x43425355 T 0x3 Trg 0 LUN 0 L 8 F 128 CL 10
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 8 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 8/8
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x3 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda:<7>usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 00 00 00 08 00 00 00
usb-storage: Bulk command S 0x43425355 T 0x4 Trg 0 LUN 0 L 4096 F 128 CL 10
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 4096 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 4096/4096
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x4 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sda1 sda2
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
usb.c: usb-storage driver claimed interface d5911ba0
USB Mass Storage support registered.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 01 80 00 60 00 9d d8 5c 1b 11 c0
usb-storage: Bulk command S 0x43425355 T 0x5 Trg 0 LUN 0 L 96 F 128 CL 6
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 96 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 40/96
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_clear_halt: result=0
usb-storage: Attempting to get CSW (2nd try)...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x5 R 56 Stat 0x0
usb-storage: Fixing INQUIRY data to show SCSI rev 2 - was 0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 60 00 9d d8 5c 1b 11 c0
usb-storage: Bulk command S 0x43425355 T 0x6 Trg 0 LUN 0 L 96 F 128 CL 6
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 96 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 40/96
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_clear_halt: result=0
usb-storage: Attempting to get CSW (2nd try)...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x6 R 56 Stat 0x0
usb-storage: Fixing INQUIRY data to show SCSI rev 2 - was 0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 01 83 00 60 00 9d d8 5c 1b 11 c0
usb-storage: Bulk command S 0x43425355 T 0x7 Trg 0 LUN 0 L 96 F 128 CL 6
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 96 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 40/96
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_clear_halt: result=0
usb-storage: Attempting to get CSW (2nd try)...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x7 R 56 Stat 0x0
usb-storage: Fixing INQUIRY data to show SCSI rev 2 - was 0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 01 80 00 60 00 9d d8 5c 1b 11 c0
usb-storage: Bulk command S 0x43425355 T 0x8 Trg 0 LUN 0 L 96 F 128 CL 6
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 96 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 40/96
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_clear_halt: result=0
usb-storage: Attempting to get CSW (2nd try)...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x8 R 56 Stat 0x0
usb-storage: Fixing INQUIRY data to show SCSI rev 2 - was 0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
